Dakota Ultrasonics TI-MINIMAX-C Bolt Tension Meter Z-182-0002
Effectively monitor your bolts during periodic shutdowns over the service life of the fastener
Also known as Z-156-0006, Z-156-0002.
| Part Number Z-156-0008 | Dakota BT1-DL Bolt Tension Monitor (MiniMax) |
| Certificate |  |
| Display Mode |
| Material thickness digits display |  |
| A-Scan | Rectified ± (half wave view), or RF (full waveform view) |
| Measurement Range | PE - 25.4 - 25,400mm (1 - 999") |
| Resolution | 0.001mm (0.0001") or 0.0001mm (0.00001") switchable |
| Measurement Rate |
| Manual | 8 readings per second |
| Velocity Calibration Range | 1250 - 13,995m/s (0.0492 - 0.5510 in/μs) |
| Temperature Compensation |  |
| Limit Alarm Mode |  |
| Memory and Data Logging | 4GB internal memory Sequential and grid batching Bitmap graphic capture and capture viewer |
| Calibration Options | Automatic, fixed, single and two-point |
| Transducer Probe Type | Single element |
| Transducer Frequency Range | 1 - 10MHz |
| Display | 1/8" VGA greyscale display (240 x 160 pixels) Viewable area 62 x 45.7mm (2.4 x 1.8") |
| Units (Selectable) | in/mm, μs, °F/°C |
| LED Backlight | On / Off/ Auto |
| Repeatability / Stability Indicator |  |
| Low Battery Indicator |  |
| Battery Save Mode | Auto |
| Transducer Connector Type | Microdot, Lemo and BNC |
| USB-C Interface |  |
| Temperature Sensor | 5 pin LEMO 1 |
| Screen Refresh Rate | 30 Hz |
| Timing | Precision TCXO timing with single shot 100 MHz 8 bit ultra-low power digitizer |
| Pulser Type | Square Wave. Selectable 100, 150 and 200 volts. Selectable options Spike, Thin, and Wide. 80 to 400ns |
| Damping | 50, 75, 100, 300, 600, & 1500ohms |
| Frequency Band | Broadband 1.8 - 19 MHz (-3dB) filter |
| Horizontal Linearity | ± 0.4% FSW |
| Vertical Linearity | ± 1% FSH |
| Amplifier Linearity | ± 1 dB |
| Amplitude Measurement | 0 to 100% FSH, with 1% resolution |
| Delay | 25,400 mm (0 - 999.9") at steel velocity |
| Measurement Gate | One gate with audible and visual alarm. Amplitude 5-95%, 1% steps |
| Setups | 64 custom user defined setups; factory setups can also be edited by the user |
| Auto Set | Automates the detection, scope, and display setting process for each individual bolt |
| Alarm Limits | Adjustable Hi/Low tolerances with visual LED's and audible beeper |
| Field Calibration | Vector or Regression correction curve for increased accuracy using Load & Stress |
| Alarm Limits Bar | Hi & Lo alarm limits for displaying an acceptable tolerance range |
| Detections | Zero Crossing |
| Time | Nanoseconds |
| Elongation | Change in length (in/mm) |
| Load | Force load applied (pounds KIP, or megapascals MPa) |
| Stress | Force for unit area stress applied (inches per inch or millimeters per millimeter) |
| %Strain | Ratio of elongation to effective length |
| Bolt Materials | Select types from a preset or custom list |
| Glue-On | Available for short bolts with minimal/short elongations to eliminate transducer placement errors |
| Part Number Z-156-0008 | Dakota BT1-DL Bolt Tension Monitor (MiniMax) |
| Operating Temperature | -10 to 60ºC (14 to 140ºF) |
| Power Supply | 3 x AA batteries and via USB |
| Battery Life | Alkaline 35 hrs, Nicad 10 hrs, NI-MH 35 hrs |
| Gauge Weight | 383g (13.5oz) - including batteries |
| Gauge Dimensions | 63.5 x 165 x 31.5mm (2.5 x 6.5 x 1.24") |