Western Instruments N88-5M-D Reaching Magnetic Pit Gauge with Digital Indicator, Inch & Metric Scales, 4.75" Blade, Two Magnetic Cartridges

See More Pit Depth Gauges

Western Instruments N88-5M-D Reaching Magnetic Pit Gauge with Digital Indicator, Inch & Metric Scales, 4.75" Blade, Two Magnetic Cartridges

See More Pit Depth Gauges
Price:
$913.00
    warrenty

    Product Description

    Western Instruments N88-5M Reaching Magnetic Pit Depth Gauge 4.75" Blade


    Western Instruments Pit Gauges assure compliance with vessel, pipeline, tank and OCTG specifications for corrosion and erosion depth measurement.
    Measuring Range: 0.0-0.5" (0.0 - 12.7 mm)
    Resolution: 0.001" (0.01 mm)
    Dial Diameter: 1.4" (35.5 mm)
    4.75" (121 mm) Blade
    Available with dial or digital indicators

    Western Instruments Pit Depth Gauges allow the Corrosion Inspector to conveniently measure Pit Depth or material loss in areas of Weight-Loss Corrosion.Various Blades for the Pit Gauges are available for different applications, including the Bridging Pit Gauge which permits Inspectors to Span or Cantilever over large areas of Weight-Loss Corrosion, to get a true measure of Pit Depth


    line
    Kit Contents 
    line

    • Western Instruments N88-5M Reaching Magnetic Pit Gauge
    • 4.75" (121mm) Blade c/w Two(2) magnet cartridges
    • Operator Instructions
    • Carrying Case


    line
    Features
    line

    Zeroing Dial Indicator

    • The vertical position of the Contact Point, needs to be Zeroed with respect to the Knife Edge of the Blade.
    • Zeroing can be accomplished in two ways; by adjusting the Height of the Dial Indicator in the Blade; or by Rotating the outer Bezel Scale while pressing on the Plunger onto a flat surface.

    Scale Zeroing
    • To quickly check the Zero Point of the Dial indicator, place the Blade on a representative smooth surface.
    • Gently press the Plunger, until the contact point touches the surface.
    • While the contact point is on the surface, loosen the Bezel Lock, and rotate the Bezel Scale until it reads '0' with respect to the pointer.

    Height Zeroing
    • Loosen the Fastener(s) holding the Dial Indicator in place.
    • Hold the Blade firmly on a Flat Surface, and gently press the body of the Dial Indicator down until the contact point touches the flat surface.
    • Carefully re-tighten the Clamp Fastener(s) or the Set Screw.
    • Any fine zeroing can be done by rotating Bezel Scale on the Indicator.
    • Height Zeroing should be done, whenever the unit is put into to use.

    Zeroing a Digital Indicator
    • Digital Indicators can be Height Zeroed or Positioned in the same way as a Mechanical Dial Indicator.
    • To Zero the Digital Indicator simply press the Zero Button when the Contact Point is on a reference point. If the Digital Indicator is Height Zeroed, press Zero when the Plunger is fully retracted.
    • To select Metric or Imperial Measurement, simply press the mm/in Button.Whennot in use, press the On/Off Button to turn the Indicator off.

    Indicator Positioning
    • The position (or rotation) of the Dial indicator can be changed by simply loosening the Clamp Fasteners or Set Screw, and rotate the Dial Indicator about the Blade.
    • After the Dial Indicator is rotated, the unit should be Dial Zeroed.


    line
    Specifications
    line

    Dial and Digital Indicators

    Metric Dial IndicatorRange:
    Resolution:
    Dial Diam.
    0.0-12.7 mm
    0.01 mm
    35.5 mm
    Imperial Dial IndicatorRange:
    Resolution:
    Dial Diam.
    0.0-0.5"
    0.001"
    1.4"
    Digital IndicatorRange:
    Dial Diam.
    0.0-0.5"
    0.0-12.7 mm
    56 mm, 2.2"

    Measuring Corrosion (Depth)

    1-Standard Tip0.040" diam.#1 Contact Point-Standard N88-S
    2-Conical Tip0.010" diam.#2 Contact Point-Conical N88-C
    3-Needle Tip0.005" diam.#3 Contact Point-Needle N88-N

    * Western offers a variety of Contact Points, which are all 0.625" (16mm) long. Any ADG Contact point can be used with our special dial indicators, but a different length may affect Height Zeroing, or the vertical position of the Dial Indicator. Contact Points are easily replaced, by extending the Contact Point , and turning it counter clockwise.


    line
    Related Products
    line

    N88L-1
    Tri-Gauge Pit Gauge

    • Lever Type Pit Gauge for Evaluation of Corrosion
    related

    line

    N88-2
    Basic Pit Gauge Center Mount 2.5" (64 mm) Blade

    • N88-2 Basic Pit Gauge Center Mount 2.5" (64 mm) Blade
    related

    line

    N88-3
    Basic Plus Pit Gauge Centre Mount 3.5" (89 mm) Blade

    • Measuring Ranges x Resolution: 14mm x 0.01mm, 0.550 x 0.001 inch
    related

    line

    N88-3M 
    Basic Plus Magnetic Pit Gauge

    • Centre mount c/w Two(2) magnet cartridges. 3.5" (89mm) Blade
    related

    line

    N88-4 
    Pocket Pit Gauge

    • Dual Edge Blade (reversible). 1.5" (38mm) long and spot base
    related

    line

    N88-5 
    Reaching Pit Gauge
    • 4.75" (121mm) Blade. End Mount Dial Indicator with Nose Cutout
    related

    line

    N88-6
    Reaching Plus

    • 6" (152mm) Blade. End Mount Dial Indicator with Nose Cutout.
    related

    line

    N88-6M
    Reaching Plus Magnetic Pit Gauge

    • 6" (152mm) Blade c/w Two(2) magnet cartridges.
    related

    line

    N88-12
    Reference Pit Gauge
    • 5.5” (140mm) long, 0.75” (19mm) wide with inverted V Edge, 2 magnet cartridges. Similar and interchangeable with Bridging Pit Gauge Main Blade.
    related


    line
    Downloads
    line

    Western Instruments N88-5M Reaching Magnetic Pit Gauges 4.75" (121 mm) Blade - Literature
    Western Instruments N88-5M Reaching Magnetic Pit Gauges 4.75" (121 mm) Blade - Data Sheet

    ADD TO CART THE ITEMS YOU WOULD LIKE TO PURCHASE
    Models Price
    $913.00
    Recommended Accessories PRICE
    $17.00
    $17.00
    $50.00
    $61.00
    $99.00
    $110.00
    $215.00
    $22.00
    $28.00