OG204 Plastic Tooke Paint Inspection Gauge IV

Description
Price: $ 495.00 up to $ 570.00
OG204 Tooke Paint Inspection Gage IV
This less expensive gage is identical to the OG202, but made of molded polycarbonate plastic.
Precision tool for inspection and thickness measurement of single or multiple coats on any substrate.

The Tooke Paint Inspection Gage IV is a precision tool for inspection and dry-film thickness measurement (in accordance with ASTM D4138) of single or multiple coats on any substrate, and for microscopic observation and measurement of substrate and film defects. The Tooke Gage uses an illuminated 50-power microscope equipped with a “universal scope” with a measuring reticle that accommodates measurement in mils, microns, and millimeters. This gauge mounts tungsten carbide cutting tips for precise incision of the work surface. Standard cutting tips are 1X, 2X, and 10X. An optional 5X tip is available. Also, a gauge can be ordered with three tips of the same size, or with a single precision-ground tip and two blanks.

Direct measurement of total dry-film coating thickness and thickness of individual coats of paint is a unique capability of the Tooke Paint Inspection Gage. Thus, in addition to routine use, it often serves as a “referee” instrument to calibrate indirect or non-destructive thickness measuring instruments.

(Note: Each universal microscope is validated before sale against a certified gage block traceable to the National Institute of Standards & Technology (NIST). An OEM calibration certificate is available for an additional fee.)


line
Applications
line

The Tooke Gage has been used to assess sandblast cleaning work, to measure plating and paint thickness on ceramics, metal, wood, and concrete, and even to measure protective backing thickness on mirrors. It is virtually the only tool for measuring paint on plastics. The quality of the incision in the film discloses much about the characteristics of the brittleness and adhesion of the material.

Other uses include assessment of substrate conditions and coating adhesion, and observation of microscopic cracking, tendency for brittleness, cratering, or other microscopic film symptoms.


line
Construction
line

The OG204 Paint Inspection Gage shown with the current
“universal” microscope, with a reticle selected for accommodation of
measurement in terms of mils, microns, and millimeters.

The gauge body is a injection-molded high-impact polycarbonate plastic. It contains the microscope and lamp batteries and the groove-cutting tungsten-carbide cutting tips mounted on the narrow side. Two adjustable threaded guide studs project from the body on the same side as the cutting tips. The tripod thus formed by the three legs (guide studs and cutting tip) provides precise alignment of the tool with the surface to be grooved. A lanyard with keeper looped through the body secures the instrument to the inspector’s wrist. The entire unit is designed for convenience and completeness in field inspection tasks.


line
Operation
line

  • A special cutting tool (the cutting tip) that is integral to the gauge is used to incise a small precision V-groove through the paint film and into the substrate.
  • Incising the V-groove with the OG204 Tooke Gage
  • Cutting tips are precision-ground from tungsten-carbide blanks.
  • The gauge in standard configuration mounts 1X, 2X, and 10X cutting tips. (An optional 5X tip is available.)
  • The gauge can be ordered in any desired configuration, such as with three tips of the same size.


line
Cutting tip ratios: A to A'
line

TipFace angleRatio
1X45° 0'A : A' = 1 : 1
2X26° 34'A : A' = 1 : 0.5
5X11° 18'A : A' = 1 : 0.2
10X5° 42'A : A' = 1 : 0.1


The tip slot is marked for the standard tip arrangement.


line

Close-up of a standard arrangement of tips, showing 2X tip extended for use


line
Principle: using the universal microscope
line

The incised V-groove is observed vertically through an illuminated microscope bearing a measuring reticle (scale). The OG202 is equipped with a “universal scope” that has a reticle that accommodates measurement in mils, microns, and millimeters. (The universal scale is metric, so conversion is necessary for English units.)

The universal microscope reticle is marked in 0.05mm (50µm) per hashmark



line
Reading the universal microscope
line

Note that in the photo below, the zero-line of the reticle is not lined up for the actual measurement (nor does it need to be; any hashmark will do). The gray/silver-colored “line” is the metal substrate; the white “line” is the (inside of the) green coating, which is what is measured visually through the scope. (See below for a different annotated version.) The cutting tip “draws” the (specifically-angled, depending on the chosen tip face) incision, which allows for calculation of the coating thickness. In this photo, the black marker has not been used to make the edge (top) of the green coating more easily seen.

In the next photo, the “zero-line” of the reticle is not lined up with the edge of the primer coating (the white line to the left of the zero-line); it is approximately centered in the substrate (gray/silver line). (This was not intentional; lining up the camera moved the gauge slightly.) “Line A” is on the edge between the substrate and the beginning of the primer-coating: begin your measurement there. “Line B” marks the top of the primer coating/beginning of the top coating (light blue). “Line C” is the incision into the top coating, made easier to see by using the black marker provided with the Tooke Gage.

Annotated close-up through universal scope


Thus, in this photo and using a “universal” scope (0.05mm hashmark space), the thickness measured for each tip equals:

1 X tip “white primer” = 2 reticle/hashmark spaces = 100 µm
“blue topcoat” = 5 reticle/hashmark spaces = 250 µm
2X tip

“white primer” = 2 reticle/hashmark spaces = 50 µm

“blue topcoat” = 5 reticle/hashmark spaces = 125 µm

10X tip

“white primer” = 2 reticle/hashmark spaces = 10 µm

“blue topcoat” = 5 reticle/hashmark spaces = 25 µm



line
Specifications
line

Smallest hashmark
measures in:
1X tip
2X tip
10X tip
Mils*2(1.97)1(0.984)0.2(0.197)
Microns**50(50.0)25(25.0)5(5.0)
Millimeters0.05(0.050)0.025(0.025)0.005(0.005)
* 1.0 mil = 0.001" = one thousandth of an inch 
**micron = micrometer (µm) = 1,000,000th of a meter



line
Universal reticle specifications
line

The injection-molded high-impact polycarbonate plastic Tooke Gage comes ready for use in a polycarbonate plastic carry case with two spare batteries, a spare LED bulb, a marking pen, a hex wrench, and a technical data sheet.

  • Standard cutting tip configuration is 1X, 2X, and 10X.
  • An optional 5X cutting tip is available.
  • Any configuration of tips may be requested (for example, three 10X tips; or a 1X, 2X, and 5X).
  • You may also order (for a lower price) a gauge with only a single cutting tip and two blank tips (spacers).
MaterialPolycarbonate plastic body
Overall dimensions4.5" x 3.5" x1"
11.4cm x 8.9cm x 2.5cm
Microscope50-power, 45-degree, illuminated
PowerTwo 15V AA drycells, plus two spares
LampLED 222 bulb plus spare
Cutting tipsPrecision-ground tungsten-carbide: usually 1X, 2X, and 10X; or as desired
Shipping Weight1.75 pounds (0.8kg)



line
Photo Gallery
line



line
Related Products
line

OG202
Tooke Paint Inspection Gauge II

  • In accordance with ASTM D4138
related


line
Downloads
line

OG204 Plastic Tooke Paint Inspection Gauge IV - Tooke Gemetry Gage
OG204 Plastic Tooke Paint Inspection Gauge IV - Current Universal Scope
OG204 Plastic Tooke Paint Inspection Gauge IV - Old Style


line
Buy Now
line


Check the items you would like to purchase then click "Add To Cart"
ItemPrice
$495.00
$445.00
$570.00
AccessoriesPRICE
$75.00
$75.00
$75.00
$75.00