https://www.abqindustrial.net/store We offer an extensive line of precision measuring and test instrumentation. We continually strive to offer unparalleled VALUE & QUALITY product and service to our valued customers. en Copyright (c) 2026 Albuquerque Industrial info@abqindustrial.net (admin) info@abqindustrial.net (admin) Tue, 09 Jun 2026 23:12:34 +0000 Zen-Cart v. v 2.1.4 14.02.2008 15:26 RSS 2.0 Feed 1440 https://www.abqindustrial.net/store/ultrasonic-testing-equipment-c-100/ultrasonic-thickness-gauges-c-100_2/ultrasonic-speciality-thickness-gauges-c-100_2_187/dakota-ultrasonics-pr-82-sonic-tester-p-392.html https://www.abqindustrial.net/store/index.php?main_page=product_reviews&products_id=392 The PR-82 has been replaced by the Dakota Ultrasonics PR-9 sonic testerFast-Scan Mode: Takes 32 readings per second and displays the minimum reading found when the transducer is removed.Measures cylinder wall thickness, deck height, chassis tubing & moreManufacturer: Dakota UltrasonicsWarranty: Five Year LimitedRange in Steel: 0.63 to 199.99 mm / 0.040 to 1.50 in Features Four readings per second for single point measurements or 16 per second in SCAN mode. Specifications RangeMeasures from 0.040 to 1.50 inches (0.63 to 199.99 millimeters) in casted materials Resolution.001 inches (0.01mm) Velocity Range.0492 to .3936 in./ms 1250 to 9999 meters/sec UnitsEnglish & Metric Transducer TypesDual Element (1 to 10 MHz). Power SourceTwo 1.5V alkaline or 1.2V NiCad AA cells. Battery LifeTypically operates for 200 hours on alkaline and 130 hours on NiCad.  Auto Power offif idle 5 min DisplayMulti-function 4.5 digit liquid crystal display with 0.500 inch numerals, backlit for use in poor light conditions KeyboardSealed membrane that is resistant to both water and petroleum products. CaseExtruded aluminum body with nickel-plated aluminum end caps (gasket sealed). Operating Temperature-20 to 120F (-20 to 50C)  Weigth, net10 ounces Dimensions2.5 W x 4.5 H x 1.24 D inches Warranty5 year limited CertificationCE Approved, Factory calibration traceable to national standards  Applications Cylinder's & Pitting Head Ports & Pipe Roll Cages Body Panels Chasis Variety of ApplicationsThe PR-82 is the first affordable Sonic Tester, utilizing state-of-the-art digital technology to produce fast and accurate readings. It requires no special training to operate. Unlike calipers, the PR-82 will measure where there is access to only one side. This makes it valuable when measuring roll cage thickness, cylinder walls (before and after boring) and heads during porting. The PR-82 measures in two modes. The first mode takes a measurement at the point you place the probe. The second is the Scan mode, which is helpful when measuring cylinder walls and roll cages. Place the probe at the bottom of the cylinder and drag it to the top, the gauge will display the thinnest reading measured. The PR-82 is a lightweight, rugged tool that is resistant to water and oil. Other features include a backlit LCD and a bar graph to indicate signal stability. The 5 year warranty indicates how we feel about the quality of the PR-82. The PR-82 can go where you go, to do the work you do, saving you time and money, making fast, accurate measurements. Transducer and Probe Information For Engine Blocks (Cylinders & Decks) One probe is usually good for use on both Cast Aluminum and Cast Iron Engine Blocks. The 2 inch radius allows the probe to measure the concave surface inside cylinders. The radius is gentle enough that the same probe can also be used to measure on the flat surfaces "decks" on the block. This one probe will work for over 90% of Cast Aluminum or Cast Iron Blocks. T-104-2120 > 0.500"/5MHz with 2 inch radius ++ In instances where the above probe does not work, or if the block is made from a very old Aluminum Cast Aluminum, then the alternate probe would be T-10404120 (0.500"/10MHz), also with a 2 inch radius. For Heads (Ports) Probe selection depends upon type of material; cast iron or cast aluminum. This probe has a 0.55" radius and is supplied with either a 1 inch wand or 9 inch wand, depending upon user preference. Cast Iron > 0.250"/5MHz with 0.55" Radius with 1 inch wand T-162-2110 with 9 inch wand T-132-2110 Cast Aluminum > 0.250/10MHz with 0.55" Radius with 1 inch wand T-162-4110 with 9 inch wand T-132-4110 For Chassis Tubing This would be used by chassis builders as well as sanctioning bodies (i.e. NHRA, ARCA, etc.). One probe is normally suitable for any application, assuming they do not want "thru-paint" capability. T-101-4000 > 3/16"-10MHz flat bottom (no radius) For "thru-paint" capability, when measuring chassis tubing for use with the PR8V T-102-2700 >0.250/5MHz Hi-Damp for use in MMX Mode Albuquerque Industrial https://www.abqindustrial.net/store/ultrasonic-testing-equipment-c-100/ultrasonic-thickness-gauges-c-100_2/ultrasonic-speciality-thickness-gauges-c-100_2_187/dakota-ultrasonics-pr-82-sonic-tester-p-392.html Sat, 04 May 2024 15:13:43 +0000 USD 392 Dakota Ultrasonics 994 PR-82 https://www.abqindustrial.net/store/images/products/pr-8.jpg 392 6 images/manufacturers_warranty/11/warranty-5-new.png